Comet system forum

tScheckSn · 19-05-2009 13:47:34

Hi,

I've a T0510 temperatur sensor and i'm the moast time not able to access the webinterface.
What ive done
1. With the factory defaults i was able to access the webinterface.
2. Ive changed the IP-Address from 192.168.1.213 to 192.168.0.177. Now i get a white plank page without sourcecode (IE and Firefox) when i want to access the IP with a Browser. With tSensor and SensorReader i can access the Sensor, see the temperature and do changes.
3. After severally trying to update the Webfrontend (Original Sourcecode from the Cometsystem Homepage) with TFTP i was able to access the Webfrontend.
4. I modyfied the Webfrontend to my own version and i was still able to access the Webfrontend and it worked fine.
5. I changed the IP address to 192.168.82.177. Now i'm again not able to access the Webfrontend, bot now i get a errormessage from my browser (404) but i'm still able to connect with tSensor and SensorReader to the device.

Configuration:
There is no Firewall between the Device and me.
IP-Address: 192.168.82.177/24
Gateway: 192.168.82.101
WWW is enabled.

Can anyone tell me what to do?

Thanks
Philipp

tScheckSn · 19-05-2009 15:49:29

I've found a second error.
When i logon with telnet and type "setup" the device gives die following output:
_______________________________________________________________
******** T-Sensor Setup Server 1-5-1.06 ********
MAC address xxxxxxxxxx
Software version V1.5.1.06 (080801) CPK6500_XPTEX
Password :----
Press Enter for Setup Mode

*** basic parameters
Hardware: Ethernet TPI
IP addr 192.168.82.177, gateway 192.168.82.101,netmask 255.255.255.0
Telnet config password set

Device name: ServerschrankSensor
MTU size: 1400

******** SMTP Configuration ********
E-mail sen
_______________________________________________________________
But than i get no more output. It stops after "E-mail sen".

HonzaD · 20-05-2009 08:11:24

Hi,

Please see your e-mail box.

John

omarangarita · 30-04-2014 02:13:41

hello; I could work please have a T0510 sensor and can not log on web, try to verify settings tsensor program nor I was able to see in the manual error and error 3 appears 4 Based on the error code -9999. This same error appears when I want to restore the factory. the led on the network connection blinks constantly.

HonzaD · 30-04-2014 11:50:58

Hi,

I am sorry but I don't understand. Please try describe your problem better.

When LEDs on RJ45 connector blinking green simultaneously at interval approximately 0.5sec, it means that main firmware is damaged. Device running at backup firmware. Main reason of this behaviour is unsuccessfully fimrware update. More information we can provide at email info@cometsystem.cz.

Jan

omarangarita · 30-04-2014 18:35:14

Hello

We have a problem with our sensor, the LEDs on RJ45 connector blinking green simultaneously, We can't log the sensor with telnet or web or some software of your website. We don’t understand about the backup firmware. How do we do? How do we running backup firmware in the device? this message is in your inbox

Thanks

HonzaD · 05-05-2014 07:38:47

Hi,

I am sorry for a late answer. We had public holiday in Czech republic.

Please check your mailbox.

Jan

Comet system forum

Temperature, Humdity,

Pressure Transmitters

and Data Loggers

#1 19-05-2009 13:47:34

T0510 Webinterface dont works.

#2 19-05-2009 15:49:29

Re: T0510 Webinterface dont works.

#3 20-05-2009 08:11:24

Re: T0510 Webinterface dont works.

#4 30-04-2014 02:13:41

Re: T0510 Webinterface dont works.

#5 30-04-2014 11:50:58

Re: T0510 Webinterface dont works.

#6 30-04-2014 18:35:14

Re: T0510 Webinterface dont works.

#7 05-05-2014 07:38:47

Re: T0510 Webinterface dont works.

Board footer